PDA

View Full Version : New Stanger Here

Torched06GT
03-10-2009, 08:41 PM
Hello everyone, my name is Billy, Im live in Marion, Arkansas, bout 30 miles west of Memphis. I own and operate a 2006 Mustang GT, Torched Red. Roush Hood scoop and side louvers, Slp Exhaust(like it loud) Full carbon dash, SOS triple gauge pod, Hurst Comp Short shifter, C & L cai with diablo 93 octane tune and lots of goodies under da hood including flames!!! also installed a GT500 chin too. I belong to the Mid South Mustang Club, we are a 70 member strong club. About 8 of us are going to the Eurakea Springs show in April so I hope to meet some of ya'll there..........
mb2
03-10-2009, 08:47 PM
welcome to the stang gang! sounds like a nice pony ya got there! if get a chance post some pics
horspwr
03-10-2009, 08:48 PM
welcome! see you in eureka...
mkeane
03-10-2009, 08:49 PM
Welcome, got any pics?
ArkansasMystic
03-10-2009, 08:49 PM
welcome to the stang gang! sounds like a nice pony ya got there! if get a chance post some pics

+1, welcome!
Torched06GT
03-10-2009, 08:54 PM
http://i141.photobucket.com/albums/r43/nascarjunkie1/WS9Q8276.jpg
http://i141.photobucket.com/albums/r43/nascarjunkie1/DSCN0231.jpg
just got the radiator cover back no pics of it yet, matches the intake cover
http://i141.photobucket.com/albums/r43/nascarjunkie1/DSCN0230.jpg
http://i141.photobucket.com/albums/r43/nascarjunkie1/Shrinersshow004.jpg
http://i141.photobucket.com/albums/r43/nascarjunkie1/WS9Q5137.jpg
http://i141.photobucket.com/albums/r43/nascarjunkie1/GTEmblem002.jpg
I also do Custom Vinyl Graphics too
ArkansasMystic
03-10-2009, 08:57 PM
Great looking car!
1low03gt
03-10-2009, 09:34 PM
Welcome aboard.Sweet looking GT!
stumbaugh
03-11-2009, 02:29 AM
Looks good, welcome to the site.
oxman
03-11-2009, 09:26 AM
Welcome to the club Billy, look forward to meeting ya!
Blackout_03
03-11-2009, 09:28 AM
welcome...good looing stang
AzianStang
03-11-2009, 11:52 AM
Welcome to the site and nice ride!
06MUSTANGGT24V
03-11-2009, 02:15 PM
Welcome! Hmmmmmmm Looks like one i know but :shrug: beats me
Terminator
03-13-2009, 10:34 PM
Welcome!
08VAPORGT
03-15-2009, 10:03 PM
Hello and nice ride, where did you get the gt500 chin and how much did it cost, if you don't mind me asking...
Lrd Vdr
03-17-2009, 12:26 PM
Welcome Billy.
hammerhead2
03-24-2009, 08:13 PM
Welcome to the board and nice GT
Torched06GT
03-31-2009, 04:59 AM
Hello and nice ride, where did you get the gt500 chin and how much did it cost, if you don't mind me asking...
I got it at Ford, and di some trimming to it to make it fit.
Recently I put a GT 500 Chin Spoiler on my car. Bought it from the Ford Dealership, cost $75.00 no shipping charge, not a bad price coming from the Dealership.

This is the piece, before it is modified.


http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall003.jpg

You want to raise your front end, prefer ramps.
http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall002.jpg

Then using a jack to support the chin to mark off where you will need to cut the plastic you wont need.
http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall006.jpg

Then using a transfer guide that I had in my tool box for years that I finally got to use, place under front end to get the countor of the bottom bumper.
http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall008.jpg

Then using a dremel with a small cutting wheel, cut off the "waffle" you wont need, looks kinda ugly till you get it all off.
http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall010.jpg


Doing both sides and mocking up to insure a proper fit, you are now ready to install. Using the 3 screws already under the bumper and drill one hole on each side near the wheel wells, I used 1/4 SS bolts with fender washers and lock nuts so they wont come off if I hit a possum or dillo...
http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall012.jpg

You will have a bunch of 1/2 holes in the chin I used these plugs I got at auto zone and some RTV silicone to hold these on.
http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall011.jpg


Put a few screws in the wheel wells our done. Took about 3 hours to do these mod.
http://i141.photobucket.com/albums/r43/nascarjunkie1/GT500ChinInstall015.jpg
http://i141.photobucket.com/albums/r43/nascarjunkie1/overlays002.jpg
bcrass
03-31-2009, 08:14 AM
Sweeeeeeeeeeeeeeeeeeeeet I Like it alot
oxman
03-31-2009, 10:27 AM
That looks really good!
08VAPORGT
04-02-2009, 12:00 AM
I just ordered that same chin spoiler for my car because my current one is getting to beat up with my car being as low as it is. I will be using your directions to put it on. I appreciate you posting that and it looks great...